FunctionPackage: profToCDocOverviewCGDocRelNotesFAQIndexPermutedIndex
Allegro CL version 8.1
Unrevised from 8.0 to 8.1.
8.0 version

start-profiler

Arguments: &key type start-sampling-p count count-list except-processes interpret-closures verbose

This function starts the collection of runtime analyzer data. It creates two new files in a temporary location for saving sample data and initializes the runtime analyzer data structures. These files are removed after analysis. See Further points, including information on temporary files in runtime-analyzer.htm.

The type keyword argument specifies the type of profile data to be collected. The choices are

Value Meaning
:time collect time data (but not space data)
:space collect space data (but not time data)
:count-only collect call-count data but no time or space data

You can collect either time data or space data but not both in a single run, but you can have call-counting data collected while collecting either time or space data. Or you can have call-counting data only collected. So the choices are:

If no value is specified for type, it defaults to :count-only if either count or count-list (or both) is non-nil and it defaults to :time if both count or count-list are nil or unspecified.

The count and count-list arguments control whether call-counting information should be collected during the run. Call count information is collected if either argument is true. Both default to nil.

count can be a positive integer or t. If it is a positive integer, a hash table with that many entries is created. If it is t, a hash table of 1000 entries is created. The table is filled with function objects specified by count-list, if any. New function objects (beyond what is specified in count-list) are added to the table as the associated function is called until the table is filled. No information is collected on function objects called for the first time after the table is filled.

count-list, if specified, should be a list of function objects (not symbols -- thus elements should be #'foo rather than foo). The hash table mentioned in the description of count just above is filled with the elements of count-list, in order, until the hash table is filled or the list is exhausted. Specifying a value for this variable ensures that functions you are interested in are call-counted. Note that if the length of the list is greater than the value of count, only the first count elements are entered in the hash table; the rest are ignored. If count-list has a true value but no value is specified for count, count defaults to 1000 (even if the length of count-list is greater than 1000).

If the start-sampling-p keyword argument is true or is not supplied then sampling is started immediately. If it is specified nil, sampling is not started until start-sampling is called. The functions start-sampling and stop-sampling can be used to control the gathering of samples while the runtime analyzer is running. The default value of this argument is t.

The except-processes keyword argument should be a list of processes or nil. This argument causes the runtime analyzer to not record data about the processes listed in this argument. Use of this argument is a good way to narrow down the extent of an analysis, if multiprocessing is being used. (In earlier releases, there was an except-stack-groups argument, which applied to certain platforms. That argument is no longer supported and a value provided for it is assumed to be a value for except-processes. A warning is signaled if except-stack-groups is specified.)

The interpret-closures argument controls the handling of closures. When interpret-closures is nil (the default) the closures are not saved and analyzed separately. When true, closures are saved and analyzed as separate profile entries, even though they may use the same template function. A function specialization called prof:closure has been added. This is valid whenever an analyzed profile exists and identifies the closures which the runtime analyzer has seen. The specialization is (prof:closure n) where n is a small integer enumerating the closures in the profile. This allows the user to grab the closure object and to do a prof:disassemble-profile on it without having to know what symbol holds its fdefinition (sometimes this is very hard).

When flat analyses and call-graphs are reported, closures are identified by (prof:closure n), followed by the printed representation of the closure object itself.

Note that if you use the Emacs-Lisp interface or the IDE (on Windows), you are using multiprocessing. The :processes top-level command lists active processes. The Process Browser in Allegro Composer (on UNIX) and the one displayed with View | Processes in the IDE (on Windows) also list processes and provide a graphic interface to include or exclude a process from profiling.

The verbose argument, if true (default is nil), causes messages about what the profiler is doing to be printed to *standard-output* during data collection.

Data can be collected for only one analysis at a time. Calling this function while data is already being collected will signal an error.

See runtime-analyzer.htm for general information on the runtime analyzer.


Copyright (c) 1998-2009, Franz Inc. Oakland, CA., USA. All rights reserved.
Documentation for Allegro CL version 8.1. This page was not revised from the 8.0 page.
Created 2009.7.29.

ToCDocOverviewCGDocRelNotesFAQIndexPermutedIndex
Allegro CL version 8.1
Unrevised from 8.0 to 8.1.
8.0 version